Methodology

How to use Bluesky Gel Polish

 Beautiful nails with deep color and beautiful shine for 2 to 3 weeks! 

Apply Bluesky Gel Polish in 6 steps:
1: If there are any unevennesses, carefully file the nails with a very fine file.
2: Degrease the nails with 70% alcohol, let it dry thoroughly.
3: Apply the Base coat and cure under a UV or LED lamp.
4: Apply the first layer of colored Gel Polish and cure under a UV or LED lamp.
5: Apply a second layer of colored Gel Polish and cure under a UV or LED lamp.
6: Apply the Top coat and cure under a UV or LED lamp.
7: Remove the sticky layer with 70% alcohol.

To prevent bubbles or wrinkling of the Gel Polish, it is important to apply each layer thinly.

One Step Gel

Same procedure as normal Gel Polish, but you don't need a Top and Base coat.
Very nice and convenient for your feet, for example, paint your toenails once and cure with the UV lamp.

Remover Wraps

Removing Bluesky Gel Polish
1: Lightly roughen the Top coat with a fine-grit file (180) or White Block.
2: Apply a little cuticle oil to the skin around the nail.
3: Apply acetone to a cotton pad, or use our Remover Wraps.
4: Wrap the nail with the cotton pad (on the nail) and aluminum foil, or put the Wrap around your fingers.
    Let it soak for 15-20 min.
5: Remove the cotton pad + aluminum foil or the Wraps.
6: Wipe away the Gel Polish; any residue can be removed with a Cuticle Pusher.

How to use Blossom Gel Polish with Blossom White Base
1: Apply Base coat, cure in UV or LED lamp.
2: Apply Blossom White base, cure in UV or LED lamp.
3: Apply a second layer of Blossom White, do not cure.
4: Create a design, e.g., a rose, with the Blossom gel using a nail art brush, cure in UV or LED lamp.
5: Apply Top coat, cure in UV or LED lamp.

Note: White Color Blossom requires Blossom Clear Base: base coat + normal black (or other color) + blossom clear base + blossom white + top coat. 

 

Gum Gel
This can be used to extend or strengthen nails.

Pre-treatment
- disinfect hands with skin disinfectant or wash hands with soap
- file nails to the desired length, gently push back cuticles with an              cuticle pusher
- clean the nail plate with 70% alcohol
- prepare the Gel brush, an orange woodstick or cuticle pusher and a small bowl of alcohol

Extension with tips
- apply a thin layer of Base Coat and cure for 30 seconds under the lamp
- take a tip and apply the Gum Gel to the inside of the tip with an orange woodstick or cuticle pusher
- dip the Gel Brush in alcohol and spread the Gum Gel evenly over the tip
- press the tip firmly onto the nail plate so that no air gets underneath
- remove any remaining Gum Gel with the Gel Brush
- cure for 1 minute under the lamp
- wriggle the tip off the nail
- if necessary, file the nail wall or nail end
- finish the nails with a Top Coat or paint with a Gel Polish

If the natural nails are long enough, but a bit thin or weak, follow these steps: - apply a thin layer of Base Coat and cure for 30 seconds under the lamp.

- apply a small ball of Gum Gel to the middle of the nail
- moisten the Gel brush with alcohol
- spread the Gum Gel evenly over the nail
- cure for 1 minute under the lamp
- if necessary, file the nail wall or nail end
- finish the nails with Top Coat or Gel Polish

 

Hard Gel
Degrease nails with 70% alcohol and let them dry.

- apply a thin layer of Base Coat and cure for 30 seconds under the lamp
- apply a thin layer of Hard Gel and cure for 1 minute under the lamp
- optionally, you can apply a second layer of Hard Gel and cure it for 1 minute as well
- apply a thin layer of Top Coat and cure for 30 seconds under the lamp
- optionally, remove the sticky layer with alcohol
You can also apply Hard Gel over Gel Polish instead of underneath.

 

Cat Eye
- apply Base Coat and cure for 30 seconds under the lamp
- apply two color coats and cure them individually.
- apply the Cat Eye Gel Polish and hold the magnet flat above the nail for 20 seconds, then cure it under the lamp (the position of the magnet determines the direction of the Cat Eye)
- apply the Top Coat
- remove any sticky layer with alcohol

 

Builder Gel

 Builder Gel (strengthening the nails)

- apply a thin layer of Base Coat
- apply a thin layer of Builder Gel (cure for 1 min)
- apply a second layer of Builder Gel (cure for 1 min)
- apply a thin layer of Top Coat
- remove the sticky layer with alcohol

Builder Gel with stencil

- apply a thin layer of Base Coat
- place a stencil tightly against the nail
- apply a layer of Builder Gel and cure for 1 min
- apply a second layer and cure for 1 min (after this you can remove the stencil)
- file the top of the nail smooth with a 180 grit file
- file to the desired length<
- apply a layer of Top Coat
- remove any sticky layer